Tuesday, October 9, 2012
Monday, September 17, 2012
Ceiling Fan Regulator - Motor Speed Control Circuit Diagram
This is a simple ceiling fan regulator circuit diagram. It is used to control the speed of a ceiling fan. In the other words it is an AC motor speed controller circuit, as because it's control the speed of a AC motor(Ceiling Fan). This ceiling fan regulator circuit built with few numbers of parts. The circuit mainly based on Z0607 TRIAC. This is a low power AC semiconductor device. Generally which is used to controlling speed of low power ac motor speed.
Circuit Diagram of Ceiling Fan Regulator :
In this ceiling fan regulator circuit, R1=500KΩ is a variable resistor that is used to adjust the fan speed. Capacitor C1 2A104J is a Polyester film capacitor.
Pin Diagram of TRIAC(T1)- Z0607:
Pin Diagram of Variable Resistor R1:
Parts List Ceiling Fan Motor Speed Controller circuit:
T1 = Z0607 -TRIACD1 = DB3 C312 -DIAC
R1 = 500KΩ -Variable Resistor
R2 = 37KΩ -Resistor
C1 = 2A104J -Polyester film capacitor.
M1 = Single Phase AC Motor (Ceiling Fan)-220V,50Hz
Saturday, July 14, 2012
555 Timer Touch Activated Alarm Circuit Diagram
This is the circuit diagram of touch activated alarm system which still activated on load shedding. Alarm system will be activated when someone touch the “touch plate” which is called trigger. In this circuit the most updated part is automatic battery activator which is made by a relay. So don’t upset on load shedding you alarm system is activated. This circuit could be used at your home door, locker, vehicle or metal gate etc.
Monday, May 14, 2012
Automatic Emergency Light Circuit Diagram
This is the simple circuit of automatic emergency light. It is called dark dependent circuit. A 555 timer IC and LDR is used for this configuration. When light fall on the LDR, its resistance is decrease and in dark position its resistance is going high. Using these characteristics of LDR, automatic emergency light is made.
LDR is called Light Dependent Resistor. Its resistance is inversely proportional to the falling light on its surface. In dark, its resistance is approximately 7k to 10k. When light fall on its surface, its resistance is decrease to less than 1k. In the circuit, a voltage dividerarrangement circuit is used here with LDR and 10K variable resistor.
When light fall on the surface of LDR, the resistance decrease to 1k. So the voltage of the timer pin-6 is greater than 2/3 of +Vcc. For this reason the output pin-3 goes low. The base voltage of transistor BC547 is less than 0.75 volt. The transistor is OFF state. So the light is OFF.
In dark position the LDR resistance increase is high so the voltage of the trigger pin-2 decrease to less than 1/3 of +Vcc. The output pin-3 goes high so the base voltage of the transistor BC547 is greater than 0.75 volt. The transistor is ON state. So the light is ON and it emits light.
Wednesday, January 18, 2012
Dual Voltage Power Supply 12 Volt
This is the simple circuit diagram of Dual Voltage Power Supply. It is used for Misc… application. This circuit is called regulated power supply. For this reason the main component of this circuit is Regulator IC. It also needs few components to built. The regulator 7812 is the positive voltage regulator and 7912 is the negative voltage regulator.
It regulates voltage from 24Volt to 12 Volt (DC). The transformer input is 110Volt to 220Volt (AC) and the output must be between 12Volt to 24Volt (AC) and current must be 500mA. In this circuit some capacitors are used as a filter for removing repole.
Sunday, October 30, 2011
Simple AM Transmitter Circuit
AM transmitter circuit that can transmit your audios to your backyard.This circuit is designed with limited the power output to match the FCC regulations and still produces enough amplitude modulation of voice in the medium wave band to satisfy your personal needs. You will love this.
These components can be easily obtained from your old medium wave radio. Q1 is provided with regenerative feedback by connecting the base and collector of Q1 to opposite ends of the tank circuit. C2 ,the 1nF capacitance , couples signals from the base to the top of L1, and C4 the 100pF capacitance ensures that the oscillation is transfered from collector, to the emitter, and through the internal base emitter resistance of the transistor Q2 (BC 109) , back to the base again.
The resistor R7 has a vital part in this circuit. It ensures that the oscillation will not be shunted to ground trough the very low value internal emitter resistance, re of Q1(BC 109), and also increases the input impedance such that the modulation signal will not be shunted to ground.
Q2 is wired as a common emitter RF amplifier, C5 decouples the emitter resistance and unleashes full gain of this stage. The microphone can be electret condenser microphone and the amount of AM modulation can be adjusted by the 4.7 K variable resistanceR5.
Tuesday, October 25, 2011
SIMPLE SWITCH TIME DELAY CIRCUIT DIAGRAM
SIMPLE SWITCH TIME DELAY CIRCUIT DIAGRAM
This Switch On Time Delay circuit should work with most any 12 volt DC relay that has a coil resistance of 75 ohms or more. The 10K resistor connected across the supply provides a discharge path for the capacitor when power is turned off and is not needed if the power supply already has a bleeder resistor.The circuit that takes advantage of the emitter/base breakdown voltage of an ordinary bi-polar transistor. The reverse connected emitter/base junction of a 2N3904 transistor is used as an 8 volt zener diode which creates a higher turn-on voltage for the Darlington connected transistor pair. Most any bi-polar transistor may be used, but the zener voltage will vary from about 6 to 9 volts depending on the particular transistor used. Time delay is roughly 7 seconds using a 47K resistor and 100uF capacitor and can be reduced by reducing the R or C values. Longer delays can be obtained with a larger capacitor, the timing resistor probably shouldn't be increased past 47K.
Subscribe to:
Posts (Atom)